| Description of Goods |
The following for use in the repair of road tractors for semi-trailers, motor vehicles principally designed for the transport of persons or goods, or fire fighting vehicles, and parts thereof: Air compressors; Bushings or sleeve bearings of bronze or powdered metal; Commutator segments of copper; Commutator insulating end rings; Crankshaft thrust collars; Diaphragms for fuel or vacuum pumps; Door bumper shoes; Electric shift control for two speed rear axles; Gasket materials, other than materials of compressed asbestos and combinations of asbestos and synthetic rubber; Graphited or oil impregnated bushings; Helical spring lock washers of steel, of an internal diameter exceeding 38 mm, steel lock washers with internal or external teeth and other metal lock washers, other than of steel; Ignition contact points; Keys for shafting; Lenses of glass for motor vehicle lamps or for light reflectors; Magnetic plugs; Metal frames for convertible soft tops; Permanent mould pistons for brake master cylinders; Propeller shaft tubes of steel bonded by rubber; Rails of lock seam section, corners, locks and catches, and unplated ventilators, of metal other than aluminum, for use in the manufacture of window sashes for bus bodies; Steel formed bottoms, metal grommets (flanges) or rings of steel, copper or brass, and blank layers of steel, for cylinder heads or manifold gaskets; Spring locators, bulkheads, spring retainers and diaphragms for spring brakes; Switches, relays, circuit breakers and solenoids and combinations thereof, including starter switch assemblies, other than automotive turn signal flasher units; Synchronizing cones or blocking rings for transmissions; Tapered discs of hot-rolled steel, with or without centre hole, for disc wheels; Timing gear blanks of laminated composition plastics; Vacuum, hydraulic or air control assemblies, other than assemblies for spring brakes; Parts of the foregoing, other than: Electric weld tubing and double wall copper brazed tubing, of an external diameter not exceeding 9.525 mm and wall thickness not exceeding 0.711 mm, for vacuum, hydraulic or air control assemblies; Hydraulic brake hoses and hydraulic brake locks; Hydraulic gear pumps to operate hoists and other accessories; Manual slack adjusters for air brake systems; Polyamide air brake tubing. |
The following for use in the repair of road tractors for semi-trailers, motor vehicles principally designed for the transport of persons or goods, or fire fighting vehicles, and chassis therefor: Ammeters; Arm rests or wheel housing lining of indurated fibre, pressed to shape, other than for motor vehicles principally designed for the transport of less than ten persons or of goods; Automatic radiator shutter assemblies; Auxiliary transmission overdrive units and controls therefor; Axle housings, one piece welded; Bearing spring shackles; Carburators; Chassis frames and steel shapes, for the manufacture therefor; Cigar and cigarette lighters, whether or not in combination with a cigarette holder, including base; Composite frame and floor structure of metal, in the rough; Control ventilator gear box; Cylinder lock barrels, with or without sleeves and keys therefor; Dash heat indicators; Fluid couplings with or without drive plate assemblies; Gasoline, oil or air gauges; Grilles not plated, polished or not before assembly, and parts thereof not plated or polished after final forming, casting or piercing, not including finish or decorative mouldings; Hinges for bodies; Horns; Instrument bezel assemblies; Instrument board lamps; Instrument panel, glove compartment, luggage compartment, hood compartment or door step lamps and wire assemblies; Locks, electric ignition, steering gear, transmission, or combinations of such locks; Mouldings of metal, with nails or prongs set in position, lead filled or not; Ornaments or identification plates of metal, unplated, not including finish or decorative mouldings, other than for past models of motor vehicles principally designed for the transport of less than ten persons or of goods; Pipe lines of tubing, rigid, covered or not, with or without fittings, other than for the motor vehicles principally designed for the transport of less than ten persons or of goods; Radiator water gauges; Reclining seat mechanisms; Refill end discs for oil filters; Speedometers; Spring covers of metal and closing strips or shapes therefor; Stampings for bodies, cowls, door pillars, fenders, front ends, hoods, instrument boards, shields or baffles, of plain or coated metal, in the rough, trimmed or not, whether or not welded in any manner before final forming or piercing but not metal finished in any degree, including such stampings incorporating pierce or clinch nuts, but excluding such stampings for door pillars, shields and baffles for current models of motor vehicles principally designed for the transport of less than ten persons or of goods; Steering wheels, rims and spiders therefor, other than for current models of motor vehicles principally designed for the transport of less than ten persons or of goods; Sun visor blanks of gypsum weatherboard; Swivel seat mechanisms; Tachometers, with or without tachographs, electric or gear driven; Throttle, spark, choke or hood lock release assemblies; Torque converters; Universal joint ball assemblies, other than cross type; Windshield or window wipers; Parts of the foregoing, other than: Blades and refills for windshield or window wipers of motor vehicles principally designed for the transport of less than ten persons or of goods; Sintered powdered metal parts of auxiliary transmission overdrive units and controls therefor; Speedometer cables and speedometer cable and housing assemblies; Parts of thermostatic controls, other than power element cups, guides, pistons, pellets, valves, flanges, top frames, bottom frames and springs. |
| Applicable Preferential Tariffs |
CCCT, LDCT, GPT, UST, MXT, CIAT, CT, CRT, IT, NT, SLT, PT, COLT, JT, PAT, HNT, KRT, CEUT, UAT, CPTPT, UKT: Free |
CCCT, LDCT, GPT, UST, MXT, CIAT, CT, CRT, IT, NT, SLT, PT, COLT, JT, PAT, HNT, KRT, CEUT, UAT, CPTPT, UKT: Free |
htshub©